|
|
|
|
|
|
 |
|
 |
|
|
 |
|
|
|
|
 |
| Item |
Size |
A |
B |
C |
D |
Fast. |
WT (lb) |
| S0950-0001 |
2" |
2.91" |
1.60" |
3.00" |
3.75" |
5/16" |
1.02 |
NOTE:
THE STRONGEST BASE AVAILABLE CAN BE USED BOTH WAYS, EITHER THE LONG OR THE SHORT SIDE IN FRONT. APPLIED TO AN UNEVEN SURFACE, IT CAN BE LEVELLED WITH ONE OR MORE SHIMS. ONCE THE STANCHION TUBE IS PLACED OVER THIS BASE, THE JOINT IS NEARLY INVISIBLE DUE TO THE BLENDING RADIUS. THROUGH HOLE FOR ELECTRICAL WIRING. |
|
 |
| Item |
Size |
A |
B |
C |
D |
Fast. |
WT (lb) |
| S0950-0002 |
2" |
2.91" |
1.60" |
3.78" |
4.75" |
5/16" |
1.19 |
NOTE:
FOR USE WITH S0950-0001 BASE ONLY, WHICH SITS FLUSH AND TIGHT INSIDE THE TOP. SPECIAL SHORT FLAT HEAD BOLTS (4) ARE PROVIDED FOR CONNECTION. BASE AND BRACKET CAN ALSO BE THROUGH BOLTED TO THE SURFACE. |
|
 |
| Item |
A |
B |
C |
D |
WT (lb) |
| S0950-0004 |
3/32" |
3.75" |
3.00" |
2.00" |
0.17 |
NOTE:
FOR USE WITH S0950-0001 MOUNTING BASE. SEVERAL SHIMS CAN BE USED TO LEVEL INTERMEDIATE STANCHIONS ON UNEVEN SURFACES TO ACHIEVE A PERFECT TOP RAIL ALIGNMENT. |
|
 |
| Item |
A |
B |
C |
D |
E |
Fast. |
WT (lb) |
| S0902-0301 |
2" |
3.21" |
4.00" |
2.75" |
0.95" |
1/4" |
0.58 |
NOTE:
OVAL WITH 2 HOLES FOR FASTENING. THIS SPECIAL PLATE ACCEPTS A STANCHION INSIDE. NOT AS STRONG OR AS “CLEAN LOOKING” AS OUR PATENTED BASE (S0950-0001), BUT ALLOWS INSTALLATIONS VERY CLOSE TO WALLS. |
|
 |
| Item |
A |
B |
C |
D |
Fast. |
WT (lb) |
| S0902-0303 |
2" |
4.00" |
1.25" |
3.00" |
# 10 Screws |
0.65 |
NOTE:
ROUND WITH 3 HOLES FOR FASTENING. THIS ROUND PLATE ACCEPTS A STANDARD STANCHION INSIDE. NOT AS STRONG OR AS “CLEAN LOOKING” AS OUR PATENTED BASE (S0950-0001), BUT ALLOWS HORIZONTAL INSTALLATION TO END RAIL AT WALL. CAN ALSO BE USED AS BASE FOR VERTICAL INSTALLATIONS. |
|
|
|
|
|
 |
| Part # |
A |
B |
C
(wall) |
Wall |
WT (lb/ft.) |
| S0950-0030 |
2" |
Custom |
0.06 (1.6 mm) |
16 gauge |
1.34 |
| S0950-0034 |
2" |
4' |
0.06 (1.6 mm) |
16 gauge |
1.34 |
| S0950-0035 |
2" |
5' |
0.06 (1.6 mm) |
16 gauge |
1.34 |
| S0950-0036 |
2" |
6' |
0.06 (1.6 mm) |
16 gauge |
1.34 |
NOTE:
UNDRILLED. SUNCOR SUPPLIES AND RECOMMENDS 16 GAUGE HIGHLY POLISHED TUBING. ALL FITTINGS ARE DIMENSIONED TO FIT IN OR OVER THIS TUBING. |
|
 |
| Part # |
A |
B |
C
(Wall) |
Wall |
WT (lb/ft.) |
| S0950-0051 |
2" |
37" |
0.06 (1.6 mm) |
16 gauge |
1.34 |
| S0950-0053 |
2" |
43" |
0.06 (1.6 mm) |
16 gauge |
1.34 |
NOTE:
THESE TWO STANDARD SIZE STANCHIONS HAVE CAREFULLY PREPARED ENDS, WHICH ARE SQUARE AND BURR FREE TO ALLOW A PERFECT MATCH WITH ALL FITTINGS. |
|
 |
| Part # |
Prep Work |
 |
| S0950-0071 |
Drill Hole |
| S0950-0072 |
Drill Hole and Fit Rived Nut |
| S0950-0073 |
Drill Dovetail Holes |
| S0950-0074 |
Drill Holes and Fit Dovetail |
| S0950-0075 |
Drill Hole and Slots For Curved Applications |
NOTE:
ADD-ONS. ALL ARE PER CUSTOMER REQUEST AND SPECIFICATIONS SUPPLIED. |
|
|
|
  |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0950-0005 |
2" |
0.25" |
0.19" |
0.38" |
2” X 16 gauge |
0.14 |
NOTE:
THE “HEART” OF THE PATENTED SUNRAILTM SYSTEM, EACH CONNECTOR (S0950-1010 TO S0950-1023) IS SUPPLIED WITH ONE DOVETAIL AND BOLT. ORDER THIS NUMBER FOR REPLACEMENT PART ONLY; INCLUDES BOLT. |
|
|
|
|
|
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0950-1010 |
2" |
1.87" |
1.75" |
1.50" |
2” X 16 gauge |
0.75 |
NOTE:
FOR USE ON END OR MID-POINT STANCHIONS WHERE HORIZONTAL RAILS RUN STRAIGHT THROUGH (180 DEGREES). FLEXIBILITY OF 5 DEGREES EITHER WAY IS BUILT-IN. THE PATENTED SUNCOR DOVETAIL UNIT WITH A SCREW BOLT IS INCLUDED IN SET. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0950-1011 |
2" |
1.87" |
1.75" |
1.50" |
2” X 16 gauge |
0.78 |
NOTE:
CAPABLE OF ABUTTING AS CLOSE AS 90 DEGREES AND AS WIDE AS 135 DEGREES ON THE SAME STANCHION. THE PATENTED SUNCOR DOVETAIL UNIT WITH A BOLT IS INCLUDED IN SET. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0950-1012 |
2" |
1.87" |
1.75" |
1.50" |
2” X 16 gauge |
0.78 |
NOTE:
CAPABLE OF ABUTTING AS CLOSE AS 90 DEGREES AND AS WIDE AS 135 DEGREES ON THE SAME STANCHION. THE PATENTED SUNCOR DOVETAIL UNIT WITH A BOLT IS INCLUDED IN SET. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0950-1020 |
2" |
1.87" |
3.00" |
1.50" |
2” X 16 gauge |
2.50 |
NOTE:
FOR STAIRS OR LEVEL CHANGES, UP AND DOWN WITH THE SAME FITTING. RAILINGS AT ANY ANGLE TO 45 DEGREES. SET INCLUDES PRE-ASSEMBLED MALE AND FEMALE SIDES, THE PATENTED SUNCOR DOVETAIL UNIT WITH BOLT AND A SPECIAL CONNECTING BOLT. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0950-1021 |
2" |
1.87" |
3.00" |
1.50" |
2” X 16 gauge |
2.20 |
NOTE:
FOR STAIRS OR LEVEL CHANGES, UP AND DOWN WITH THE SAME FITTING; USED WHEN STAIRS ARE AT RIGHT ANGLE TO A RAILING. RAILINGS AT ANY ANGLE TO 45 DEGREES. SET INCLUDES PRE-ASSEMBLED MALE AND FEMALE SIDES, THE PATENTED SUNCOR DOVETAIL UNIT WITH BOLT AND A SPECIAL CONNECTING BOLT. |
|
|
|
|
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0950-1022 |
2" |
1.87" |
3.00" |
1.50" |
2” X 16 gauge |
2.20 |
NOTE:
FOR STAIRS OR LEVEL CHANGES, UP AND DOWN WITH THE SAME FITTING; USED WHEN STAIRS ARE AT RIGHT ANGLE TO A RAILING. RAILINGS AT ANY ANGLE TO 45 DEGREES. SET INCLUDES PRE-ASSEMBLED MALE AND FEMALE SIDES, THE PATENTED SUNCOR DOVETAIL UNIT WITH BOLT AND A SPECIAL CONNECTING BOLT. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0950-1023 |
2" |
1.87" |
1.50" |
1.10" |
2” X 16 gauge |
1.77 |
NOTE:
THIS PART IS DESIGNED TO WORK IN CONJUNCTION WITH ALL FITTINGS ON PAGE 134, AND PERMITS A SMOOTH TRANSITION OF A HANDRAIL UP OR DOWN. SET INCLUDES PRE-ASSEMBLED MALE AND FEMALE SIDES AND A SPECIAL CONNECTING BOLT. |
|
 |
| Part # |
A |
B |
C |
Tube |
WT (lb) |
| S0950-0028 |
2" |
1.87" |
1.16" |
2” X 16 gauge |
0.30 |
NOTE:
FLAT TOP CAP CLOSES STANCHION AFTER INSTALLATION IS COMPLETE. MICROSTARTM CABLE CONNECTIONS ARE ACCESSIBLE FROM THE TOP FOR MAINTENANCE BY PRYING OFF THE CAP. CHOICE OF THE CAP IS ACCORDING TO DESIRED LOOK OF INSTALLATION. |
|
 |
| Part # |
A |
B |
C |
Tube |
WT (lb) |
| S0950-0029 |
2" |
1.87" |
1.54" |
2” X 16 gauge |
0.25 |
NOTE:
DOME TOP CAP CLOSES STANCHION AFTER INSTALLATION IS COMPLETE. MICROSTARTM CABLE CONNECTIONS ARE ACCESSIBLE FROM THE TOP FOR MAINTENANCE BY PRYING OFF THE CAP. CHOICE OF THE CAP IS ACCORDING TO DESIRED LOOK OF INSTALLATION. |
|
 |
| Part # |
Size |
# In Package |
WT (lb) |
| SCREWS ONLY |
| S0910-2015 |
5/16" UNC-1/2" LENGTH |
20 |
0.30 |
REPLACEMENT SCREWS FOR ANCHORING MOUNTING BASE TO BASE BRACKET.
|
| SCREW WITH WASHER AND NUT |
| S0910-2045 |
5/16" UNC -1-3/4" LENGTH |
20 |
0.80 |
| S0910-2065 |
5/16" UNC -2-1/2" LENGTH |
20 |
1.00 |
| S0910-2100 |
5/16" UNC -4" LENGTH |
20 |
1.60 |
| MOUNTING BOLTS SETS TO THROUGH-BOLT MOUNTING BASE TO SUPPORTING SURFACE. ALSO SUITABLE TO BOLT BASE TO BRACKET AND THEN THROUGH-BOLT TO SUPPORTED SURFACE. |
|
|
|
|
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0902-0101 |
2" |
1.87" |
3.95" |
0.98" |
2” X 16 gauge |
0.69 |
NOTE:
ALTERNATIVE END FITTING FOR USE WITH CONTINUOUS TOP RAIL. 90 DEGREE ANGLE, ROUND ELBOW. CAN BE COMBINED WITH A SHORT TUBE AND 90 DEGREE CORNER (S0902-0102) TO FORM A TRANSITION FROM A STRAIGHT RAIL UP OR DOWN STAIRS. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0902-0102 |
2" |
1.87" |
3.95" |
0.98" |
2” X 16 gauge |
0.70 |
NOTE:
ALTERNATIVE END FITTING FOR USE WITH CONTINUOUS TOP RAIL. 90 DEGREE CORNER IS MOSTLY USED ON THE LAST STANCHIONS TO TERMINATE THE TOP RAIL. CAN BE COMBINED WITH A SHORT TUBE AND ROUND ELBOW (S0902-0101) TO FORM A STRAIGHT RAIL UP OR DOWN STAIRS. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0902-0104 |
2" |
1.87" |
2.60" |
0.25" |
2” X 16 gauge |
0.40 |
NOTE:
CONNECTING PIECE TO JOIN AND ALIGN TWO TUBES. ONLY NEEDED FOR LONG TOP RAILS USING CENTER GUIDE (S0902-0305) OR FIXED MID SUPPORT (S0902-0304), OR FOR STAIR RAILS USING ADJUSTABLE SUPPORT (S0902-0408). |
|
 |
| Part # |
A |
B |
C |
D |
E |
WT (lb) |
| S0902-0105 |
2" |
1.87" |
4.70" |
3.37" |
0.98" |
1.10 |
NOTE:
ALL ANGLES ARE 90 DEGREES. ALTERNATIVE CENTER STANCHION FITTING FOR USE WITH CONTINUOUS TOP RAIL (WITH STANCHIONS BUTTING TO UNDERSIDE). |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0902-0106 |
2" |
1.87" |
3.36" |
0.98" |
2” X 16 gauge |
1.03 |
NOTE:
ALL ANGLES ARE 90 DEGREES. ALTERNATIVE CORNER FITTING FOR USE WITH CONTINUOUS TOP RAIL, (WITH STANCHIONS BUTTING TO UNDERSIDE). |
|
|
|
|
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0901-0305 |
1-1/2" |
1.87" |
4.28" |
0.98" |
1-1/2” X 16 gauge |
1.00 |
| S0902-0305 |
2" |
1.87" |
4.28" |
0.98" |
2” X 16 gauge |
1.12 |
NOTE:
ALTERNATIVE CENTER STANCHION FITTING FOR USE OF TOP RAIL AS A HANDRAIL. FITTING ALOWS HAND TO SLIDE ALONG TOP AND SIDES OF RAIL WITHOUT INTERFERENCE FROM STANCHION. NOTE THAT BOTH FITTINGS REQUIRE A 2” STANCHION, ONLY THE HANDRAIL SIZE DIFFERS. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0901-0401 |
1-1/2" |
2.76" |
3.41" |
1.88" |
1-1/2” X 16 gauge |
0.65 |
| S0902-0401 |
2" |
2.76" |
3.41" |
1.88" |
2” X 16 gauge |
0.70 |
NOTE:
90 DEGREE ANGLE. SPECIAL CENTER FITTING FOR WALL MOUNTED HANDRAIL ONLY. FITTING ALLOWS HAND TO SLIDE ALONG TOP AND SIDES OF RAIL WITHOUT INTERFERENCE FROM STANCHION. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| LEFT: |
| S0901-0402 |
1-1/2" |
2.76" |
3.41" |
1.88" |
1-1/2” X 16 gauge |
0.65 |
| S0902-0402 |
2" |
2.76" |
3.41" |
1.88" |
2” X 16 gauge |
0.70 |
| RIGHT: |
| S0901-0403 |
1-1/2" |
2.76" |
3.41" |
1.88" |
1-1/2” X 16 gauge |
0.65 |
| S0902-0403 |
2" |
2.76" |
3.41" |
1.88" |
2” X 16 gauge |
0.70 |
NOTE:
90 DEGREE ANGLE. SPECIAL END FITTING FOR WALL MOUNTED HANDRAIL ONLY. FITTINGS ARE CLOSED ON ONE END TO CREATE A PROFESSIONAL RAIL END. TYPICALLY ONE LEFT HAND AND ONE RIGHT HAND IS USED PER HANDRAIL. |
|
 |
| Part # |
A |
B |
C |
D |
Tube |
WT (lb) |
| S0902-0304 |
2" |
1.87" |
0.44" |
0.36" |
2” X 16 gauge |
0.40 |
NOTE:
ALTERNATIVE CENTER STANCHION FITTING WHERE TOP RAIL NEEDS TO SPAN SEVERAL STANCHIONS IN ONE PIECE. FITTING IS FIRST SCREWED TO UNDERSIDE OF RAIL BEFORE BEING INSERTED INTO STANCHION. REQUIRES PERFECT ALIGNMENT FOR PROPER FIT. |
|
 |
| Part # |
A |
B |
C |
D |
Fast. |
WT (lb) |
| S0902-0408 |
2" |
1.87" |
2.56" |
3.15" |
2” X 16 gauge |
0.65 |
NOTE:
SPECIAL ADJUSTABLE CENTER STANCHION FITTING FOR USE OF TOP RAIL AS STAIR HANDRAIL. |
|
|
|
|
|
 |
| Part # |
A |
B |
C |
D |
Thread |
WT (lb) |
| S0950-0064 |
1/8" |
31-5/8" |
1.50" |
3.00" |
1/4" X 20 UNC |
0.10 |
| S0950-0065 |
1/8" |
37-5/8" |
1.50" |
3.00" |
1/4" X 20 UNC |
0.12 |
| S0950-0066 |
5/32" |
31-5/8" |
1.50" |
3.00" |
1/4" X 20 UNC |
0.15 |
| S0950-0067 |
5/32" |
37-5/8" |
1.50" |
3.00" |
1/4" X 20 UNC |
0.18 |
NOTE:
BALUSTER ASSEMBLIES MADE FROM 316 STAINLESS STEEL 7 X 7 WIRE ROPE AND TWO SPECIAL SWAGE STUDS, ONE LEFT AND ONE RIGHT HAND. REQUIRES EXCLUSIVE RIGHT HAND AND LEFT HAND RIVET NUTS IN RAILS TO ALLOW TENSIONING. |
|
 |
| Part # |
A |
B |
C |
Thread |
WT (lb) |
| S0950-0061 |
5/16" |
33-3/8" |
2.00" |
5/16" X 18 UNC |
0.20 |
| S0950-0062 |
5/16" |
39-3/8" |
2.00" |
5/16" X 18 UNC |
0.24 |
NOTE:
SOLID 316 POLISHED ROD, WITH RIGHT HAND UNC THREAD ON ONE END FOR EASY INSTALLATION INTO LOWER RAIL. REQUIRES EXCLUSIVE RIGHT HAND UNC RIVET NUT FOR INSTALLATION. SPINDLE IS SCREWED INTO LOWER RAIL FIRST; AFTER TOP RAIL IS FITTED TO STANCHIONS, THE SPINDLE IS UNSCREWED UNTIL IT TOUCHES THE INSIDE TOP. |
|
 |
| Part # |
A |
B |
C |
D |
WT (lb) |
| S0950-0008 |
2" |
2.15" |
2.34" |
1.32" |
0.97 |
NOTE:
RUBBER PADS AVAILABLE FOR SNUG FIT ON 3/8” OR 1/2” GLASS. FITTING IS FIRST ATTACHED TO STANCHIONS. AFTER ONE SIDE PART IS REMOVED, THE GLASS IS FITTED AND ADJUSTED BEFORE RE-INSTALLING THE REMOVED PART. |
|
 |
| Part # |
A |
B |
C |
D |
E
(West) |
WT (lb) |
| 12 VOLT DC |
| S0801-0000 |
1/4" |
0.312" |
0.09" |
0.825" |
24.00" |
0.02 |
| 24 VOLT DC |
| S0801-0002 |
1/4" |
0.312" |
0.09" |
0.825" |
24.00" |
0.02 |
| SPACER: |
| S0841-0030 |
30º |
|
|
|
|
|
NOTE:
SMALLEST SELF CONTAINED LED ON THE MARKET, ONLY NEEDS 1/4" BORE FOR HOUSING OR 3/8" IF USED WITH GROMMET. MICROSTARTM FITS INTO RAILINGS USING GROMMET. SUNCOR RECOMMENDS SPACING OF 24” +/- BETWEEN LIGHTS FOR BEST EFFECT. |
|
 |
| Part # |
A |
B |
C |
Hole Size |
WT (lb) |
| S0385-0005 |
3/16" |
0.46" |
0.50" |
3/8" |
0.01 |
| S0385-0007 |
1/4" |
0.46" |
0.50" |
3/8" |
0.01 |
| S0385-0008 |
5/16" |
0.60" |
0.63" |
1/2" |
0.02 |
| S0385-0010 |
3/8" |
0.60" |
0.63" |
1/2" |
0.03 |
NOTE:
SPECIAL FITTING WITH “KNIFE THREADS” ON THE OUTSIDE AND STANDARD UNC ON THE INSIDE. USED TO CONNECT HORIZONTAL WIRE ROPE TO WOODEN POSTS INSTEAD OF STAINLESS STANCHIONS. |
|
|
|
  |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
